- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.
$7.99 - $9.99
- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.
- 4140 Chromoly - 3 Possible peg positions for longer peg life - 14mm with 3/8-inch adapters included - 4 inches (length) x 1-3/8 inches (outer diameter) - Sold in pairs - 8.75 oz (17.5 oz for a pair)
The Slim by Four is a BMX-specific brake pad with a symmetrical shape designed for both forwards and backwards braking. A custom inner frame helps to stiffen the pad and prevents excessive braking power from being lost to flex. SPECS - Clear and Gum colored “Soft” compound pads provide extra grip on powder coated rims. - Black “Normal” compound Slim-By-Four pads are the most popular pad choice for most riders.
Odyssey's 49er is a traditional-looking 4-piece bar that uses multi-butted main tubing, traditional 7/8" crossbar for strength, larger radius bends for greater durability, and welded end caps to reduce flex. These bars have a post-weld heat-treating which is guaranteed against manufacturer’s defects. SPECS - 9-inch Rise - 29-inch Width - 1.5° Upsweep - 12° Backsweep - 2lbs 3.4 oz
A classic knobby version of the Aitken signature tire. Traditionally a more dirt-specific tire but the tire’s fast rolling center tread allows it to be used on all terrains. - 20 × 2.35 only Single ply casing
Mike Aitken's popular signature tires for street and dirt. Ideal for use at high speeds. - 20 × 2.25, and 20 x 2.45 Dual ply casing
The Antigram is a 36-H rear hub that is strong, light and reasonably priced with in-bound axle bolts that is both RHD/LHD switchable and guard compatible. SPECS - 2014-T6 forged aluminum hub shell - 6903RS sealed cartridge ball bearings - 9-T driver with 3-Pawn independent springs design and precision caged needle bearings - RHD/LHD switchable WEIGHTS - With 14mm Chromoly Axle: 14.5oz / 411g - MEASUREMENTS Drive Side - Effective Flange Diameter: 49mm - Non-Drive Side Effective Flange Diameter: 49mm - Drive Side Flange to Center Distance: 30mm - Non-Drive Side Flange to Center Distance: 30mm
For the Bluebird chain, Odyssey took the proven and reliable KMC 510-HX chain and added a permanently attached, factory installed half-link to one end. When the chain is trimmed to size you can easily decide whether or not to use the half-link. Original factory assembled pin joints are radically stronger than workshop assembled ones, so this is a huge benefit.
- Sold in pairs - Allen wrench included
A traditional clutch-based coaster hub design that eliminates all of the problematic elements on ordinary hubs and only keeps the parts that work. A new, super-strong axle, bearing configuration, and drag mechanism design stops the need for constant repairs. Equipped with external slack adjustment (can be adjusted without removing the rear wheel), and a plastic hub guard. FEATURES - Super-durable bearing arrangement throughout - Maximum strength axle design Unique external slack adjustment feature - Super-durable drag mechanism design GUARD OPTIONS - Plastic hub guard included (but optional to use) MEASUREMENTS - Drive Side Effective Flange Diameter: 56mm - Non-Drive Side Effective Flange Diameter: 49mm - Drive Side Flange to Center Distance: 27.5mm - Non-Drive Side Flange to Center Distance: 27.5mm
- Press fit designed to work the hub's non-drive side collar.
$64.99 - $74.99
Using Odyssey's popular TL48 stem as a springboard, Tom Dugan's signature DGN stem is a classic top load design. FEATURES - Six bolt clamping configuration - Headset pre-load bolt recess (32mm diameter) - 6061-T6 aluminum, CNC machined
- For 19mm crank spindles and threaded Euro bottom bracket frames. - High-quality four bearing design with aluminum cups.
Chase Gouin’s signature tire. Predictable during tight turns and made to roll smooth at high speeds. Horizontal tread grooves provide shoe traction only when you need them to. This modern interpretation of one of the most popular tires ever made is used regularly by street riders too. Now available with a Special Compound tread durometer for polished indoor floors. 100 PSI, of course.
6061 aluminum with precision sealed mechanism bearing and lower (17mm) stack height.
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)
The Gyro G3 upper top plate is designed for use with the G3 detangler.
- Straight gauge spokes with a proprietary grade of stainless steel that is as good or better than the materials used by the world’s most renowned spoke makers. - Sized and dimensioned specifically for BMX.
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
A total redesign of Odyssey's popular MDS sprocket. With a built-in full guard, this sprocket lives up to its name, helping to protect your chain from anything you can throw at it. Sprocket thickness increases towards the guard area for greater strength. Compatible with all chain widths. - 7075 Aluminum
This is Odyssey's top-of-the-line brake cable that ties together all of their most advanced braking technology. - Utilizes the original BMX Linear Slic Kable housing to prevent binding when the bars are rotated. - Factory installed ferrule ends with inner volcano shape to prevent housing blow out; a Linear Slic Kable standard since 2008. - Specially coated inner wire for ultra low friction, a proven feature resurrected from their once famous Brakeline cables. - Gyro lug included at one end of the inner wire for use with detanglers. - 60-65mm in length. - Black
The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing (2.9 oz). - Black - 60 – 65mm
The M2 lever works with a single cable or Odyssey's dual cable system. - Improved braking power for Gyro users - Left/Right hand compatible
- Made to fit crank spindles and press-fit Mid BB frames. - Simple and easy to install. - Includes an assortment of spacers to optimize chainline and crank clearance. - Odyssey 6061-T6 aluminum dust spacer included.
The Monolever was an instant classic and has become a clear favorite with pro riders around the world because of its familiar feel, smooth edges and variety of handle options.
A huge leap forward in pedal technology that results in a simpler overall design. Extremely lightweight plastic bodies eliminate the need for bearings and allow for a spindle that is significantly stronger than normal. Metal pins make the pedal very grippy, and the pedal will still function normally when pins are removed from one side for grind tricks. No flimsy outboard end caps. Pedal body halves are easy and inexpensive to replace – instead of replacing the whole pedal. - 9/16-inch, heat-treated, 4140 chromoly spindle - Proprietary high-strength plastic composite
Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.
It’s a traditional straight up pivotal design with a 200mm length.
Designed using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 10mm, 3mm and 2mm (15mm total) - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1-1/8 integrated headset. - 45º tapered bearings 41.8mm outer diameter (fits 42mm BMX head tubes).
Page 1 of 2 Next page