Tools

Designed to press in all current wheels mfg bottom brackets! our universal bottom bracket frame drift is designed to press all current wheels mfg bottom bracket cups in to your frame. The adapter is machined with multiple steps to fit common bottom bracket shell inside diameters listed in the compatibility tab below. Each step is laser etched with the diameter size. Drift can also can be used as a frame bottom bracket shell sizing guide! - Inner hole sized to fit 1/2" threaded rod. (Not for use with our Press-1 or Press-4 ) - Compatible with any other press with a 1/2" diameter rod - Recommended for use with Wheels Mfg BP0006, BP0007 - Machined aluminum - Anodized red - Sold individually We do not recommend it for use with press with a rod diameter less than 1/2". When used with a smaller rod, it is almost impossible to prevent the cups or bearings from pressing in straight.

Shimano Direct Mount Chainring Socket

Receiver cup sleeve for Wheels Mfg. sealed bearing extractors. Machined aluminum sleeve, anodized red. - 1/2-inch thru hole to fit over their 1/2-inch threaded rod press handles - Part of a system that requires additional pieces to function

Receiver cup for Wheels Mfg. sealed bearing extractors. Machined aluminum cup, anodized red with 60mm OD and 52mm ID. - 1/2-inch thru hole to fit over Wheels Mfg. 1/2-inch threaded rod press handles - This receiver cup is part of a system that requires additional pieces to function

- Heavy duty double-ended steel lockring wrench - 10.5" long for plenty of leverage, fits most bottom bracket lockrings

The Bottom Bracket Gauge Tool was designed to provide all the necessary measurements to identify the proper bottom bracket for a specific bike configuration. A metric scale runs along the long edges for measuring bottom bracket shell width and crank spindle lengths. Durable red anodized aluminum with laser etching. Overall size is 7" x 3" x 0.125". The gauge can measure: - bottom bracket width - bottom bracket shell inner diameter - crank spindle length - crank spindle diameter - bearing inner diameter Specifications: Measures crank spindle diameters: 22mm, 24mm, 29mm, 30mm Measures bearing inner diameters: 22mm, 24mm, 29mm, 30mm Measures bottom bracket shell inner diameters: 37mm, 41mm, 42mm, 46mm Measures bottom bracket shell widths: 61mm, 68mm, 73mm, 79mm, 86.5mm, 90mm, 92mm, 95mm, 100mm, 120mm, and 132mm Measures crank spindle lengths up to 180mm

- E-bike socket designed for installing and removing compatible cassettes on Bafang hub-drive motors without removing motor wiring - Center clearance for E-Bike wiring is 0.812". 12-spline 23mm OD tool fittings - Made in the USA

Sealed bearing extractor for 29mm ID bearings. Extractor has 1/2" thru hole for use with our 1/2" threaded rod press handles. - This extractor is part of a system that requires additional pieces to function.

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

- Sealed bearing extractor with 1/2-inch thru hole for use with Wheels Mfg. 1/2-inch threaded rod press handles - Part of a system that requires additional pieces to function

This Wheels Mfg. Double End Bottom Bracket wrench fits 16-notch bearing cups with an outside diameter of 44mm as well as 16-notch bearing cups with an outside diameter of 48.5mm. - Machined aluminum - Anodized red. - Compatible with all current Wheels Mfg bottom brackets with notched cups

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body - Anodized in Wheels MFG red.

Wheels Manufacturing Sealed Bearing Extractor - 10mm Fits the following bearings: - 6000 - 6200 - 6800 - 6900

Wheels Manufacturing Sealed Bearing Extractor - 12mm Fits the following bearings: - 6001 - 6801 - 6901

Wheels Manufacturing Sealed Bearing Extractor - 15mm Fits the following bearings: - 6002 - 6702 - 6802 - 6902 - 15267 - 15268

Wheels Manufacturing Sealed Bearing Extractor - 17mm Fits the following bearings: - 6003 - 6803 - 6903 - 17287

Individual extractor for removing 6806 sealed bearings with 29mm inside diameter. These bearing extractors grip the inside race of a sealed bearing, allowing the bearing to be tapped out of the hub shell or frame component. Insert the extractor into the bearing, tighten one side with a matching wrench, and the collet expands to grip the inside of the bearing. Tap the extractor bearing out together with a punch and hammer. All extractors are size specific! If attempting to remove a bearing of a different size than the extractor, you will permanently damage or break the extractor. If the extractor is smaller than the bearing, try using a shim between the extractor and the bearing to get the tightest fit before tightening the extractor bolt.

Wheels Manufacturing Sealed Bearing Extractor - 10mm Fits the following bearings: - 6704 - 6804 - 6904

- These sockets have a machined 3/8" drive, which can be used to allow 3/8" drive torque wrenches to be attached and locks onto 1/2 inch UNC press rod for secure and easy installation of thin flanged bottom brackets - Machined 6061 aluminum in anodized red - Made in the USA

- These sockets have a machined 3/8" drive, which can be used to allow 3/8" drive torque wrenches to be attached and locks onto 1/2 inch UNC press rod for secure and easy installation of thin flanged bottom brackets - Machined 6061 aluminum in anodized red - Made in the USA

Thin flange bottom bracket socket designed to create a tight grip on thin flange bottom bracket to avoid slipping while torquing cups into bike frames. This single-sided socket is used for installing and removing 48.5mm, 16-notch bottom bracket cups. The socket has a machined 3/8" drive, which can be used to allow 3/8" drive torque wrenches to be attached and locks onto 1/2 inch unc press rod for secure and easy installation of thin flanged bottom brackets. Machined 6061 aluminum anodized red

- SRAM Thin Flange T47 Bottom Bracket Socket Designed to create a tight grip on thin flange bottom bracket to avoid slipping while torquing cups into bike frames. - This single-sided socket is used for installing and removing 52mm, 16-notch bottom bracket cups. - The socket has a machined 3/8" drive, which can be used to allow 3/8" drive torque wrenches to be attached and locks onto a 1/2 inch UNC press rod for secure and easy installation of thin flanged bottom brackets. - Machined 6061 Aluminum Anodized Red

BB30 service kit for SRAM DUB cranks. - Includes (2) Enduro 6806/29 ABEC-3 sealed bearings and 2 retaining clips - Bearing Dimensions: OD: 42mm / ID: 29mm / Width: 7mm - Enduro ABEC-3 bearings - Use with SRAM DUB cranks Note: SRAM DUB cranksets are not designed to work in 68mm or 73mm wide shells with inboard bearings. Use only if your frame is a direct-fit bearing system, and the BB shell width is 86.5mm or wider.

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

- Similar to its big brother but at a fraction of the size. The new and more efficient Adjustable Press Stop Mini will make life easier for mechanics as it allows for quick and accurate positioning in places where space is tight at the press of a button. - Adjustable Press Stop slides along 3/8" ACME threaded press rod when the button is depressed and can be placed quickly to secure drifts, spacers, and cups when completing maintenance or installation of bike headsets, bottom brackets, and bearings. - Compatible with new and existing Wheels MFG press kits which utilize a 3/8" ACME threaded rod - Compatible kits include: Press-4, ST0006, Press-1 - Machined aluminum body - Anodized in Wheels MFG red. - Durable steel button - For use with 3/8" ACME threaded press rod (Sold Separately)

- Allows for quick and accurate positioning at the press of a button - Slides along 1/2" UNC threaded press rod when the button is depressed and can be placed quickly to secure drifts, spacers, and cups when completing maintenance or installation of bike headsets, bottom brackets, and bearings

Use this double-sided socket tool for installing and removing both 48.5mm and 44mm 16-notch bottom bracket cups. Socket is machined for 1/2-inch drive, but a 3/8-inch to 1/2-inch adapter is included so you can use it with 3/8-inch drive torque wrenches. - Compatible with all Wheels Manufacturing bottom brackets that have 48.5mm or 44mm, 16-notch spline patterns - Also compatible with FSA MegaEVO BB cups, Shimano, SRAM/Truvativ, Campagnolo Ultra Torque, and FSA - Machined 6061 aluminum - Anodized red